Name:

Contact:

Company:

Email:

Comments:


The test bench tests mechanical and electrical endurance characteristics of MCB for quality assessment purposes

MCB Endurance Test Bench (IEC 60898-1 Clause 9.11)

Lab Test

The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.

This test equipment also covers testing as per Indian Standard IS 8828 as well as Indonesian Standard SNI 8528-1 (BSN)

Completely stand alone unit after initial configuration of test parameters

Smartly designed pneumatic fixture to accommodate more type of MCBs

Safety / Diagnostic Feature: Contact Weld / Contact Open indication for opening or welding of current carrying contacts inside the panel

Micro controller based operation enables input settings as per IEC as well as user configurable for other settings.

Graded inductors for accurate power factor output Industrial grade wire wound resistors enables continuous operation without overheating of the load bank

The user may simultaneously test MCBs of different brands and compare the tst results (Ideal Application for Test Labs and Certification Agencies).

User friendly digital interface to input test parameters

MCB Range Selection: Through neatly labelled shorting links

Input 380 / 415 440 V, 50 / 60 Hz (User Specified), 3 phase, 100 A continuous

Load Current: 0.5 A to 100 A

Electro Magnetic Counter: To count the number of operations

Pneumatic Pressure required: 6 Bar

Metering: i) Micro-Controller based Programmable Timer ii) 3 phase digital ammeter iii) 3 phase digital voltmeter iv) 3 phase digital power factor meter

Ratings of MCB covered: 0.5, 1, 1.6,2, 3, 4, 6, 8, 10, 13, 16, 20, 25, 32, 40, 45, 50, 63A, 80A, 100A, 125 A selectable with Shorting Links

The bench can be customised in to 0.5- 63, 6- 63, 0.5 – 32, 0.5 – 125 A current range. Further, the user may choose if he wants a micro-controller based control or a PC / PLC based control. The fixture is designed as per the MCB samples provided. (A similar equipment is offered to test RCCBs and RCBOs for endurance testing that differs in load parameters and fixture design, please refer the relevant section if you are interested).

The test bench tests mechanical and electrical endurance characteristics of MCB for quality assessment purposes.

Products From Same Category

The MCB Thermal Trip Calibration Test Bench is a fully automatic stand alone equipment
4 Station Thermal & Calibration Test Bench
This is designed for Testing of MCB to carry out “Test of Instantaneous Tripping
MCB Magnetic (Instantaneous) Trip Test Bench
The 28 days Test Bench can work in single as well as three phase mode
3-Phase-28-Days Temp-Rise-Test
It is a programmable High Voltage Tester for MCB equipments
High-Voltager-Tester
The test is intended to check the instantaneous trip (magnetic trip mechanism) characteristics of an MCB as per its rating and curve at a conveniently low voltage
MCB-Instantaneous-Trip-Test-Bench
The test, similar to that of an MCB, is carried out to measure the power loss across each pole
MCB Temperature Rise and Power Loss Test Bench
The tester is used to carry out the 1.13 and 1.45 test, optionally inside a heated environment (temperature chamber)
MCB Tripping Current Characteristic Test Bench
The test bench is primarily designed to hold and connect multi pole MCBs for thermal verification
MCB-Thermal-Calibration-Verification-Test-Bench
This product is used by leading MCB manufacturers on their lab & production floor
PC-Based-Thermal-+-Magnetic-Test-Bench-for-MCB
Glow Wire Test Apparatus – GWT A2 (Automatic)
Glow Wire Test Apparatus – GWT A2 (Automatic)
The tester is used to simulate a particular impulse (1.2 / 50 microsecond) so as to assess the insulation characteristics of a breaker against a real world impulse experienced by the MCCB
Impulse Tester 10,700mfd
The product is used to measure the millivolt drop at a high dc voltage or to assess the micro-ohms of an MCB
millivolt drop tester